Is this a good 6.5 magazine?

[garikfox]

Hello Friends, I was wondering If I did okay on the correct 6.5mm magazines. I purchased three of them. I'm assuming these are the best ones to use?

Thanks,
-Garik

[LRRPF52]

Ealanders have been good to me. AA typically does additional inspection on the magazines they carry as an extra layer of QC.

[garikfox]

Thanks! Looks like I did good than. Thanks again

[VASCAR2]

The E-Lander mags have stout springs when new. I suggest you load your mags to capacity until your ready to go shoot. Some forum members have cycled the magazines spring multiple times with a wooden yard stick or wooden dowel rod to help wear in the spring.

I have only had one faulty E-Lander magazine. That mag was a twenty four round mag with rough welds on the spine which was putting drag on the follower. A couple passes with a flat file fixed that mag. All my other E-L mags have proven reliable, especially after they’ve been used a few times.

[lazyengineer]

I'm happy with them. Just ran a full one in a 3-gun practice run yesterday with Wolf Steel. Ran great.

[Bonas]

I like the Duramag/C-Products defense mags best. I've had both those and E-Landers. E-Landers cycled fine but were too hard to unload to be worth fooling with for me.

[garikfox]

Awesome thanks guys

[garikfox]

Wow you guys were right these steel mags are very hard to fill up. They hold 24rds and I could barely push in the 20th rd. wow lol

[eggman918]

When I acquired my AR Grendel I got 3 ea. E-landers and 3 AR-stoner 10 round mags and both brands have performed well so far with ~600 rounds total through them.
With that being said the fit and finish of the E-landers is superior in every way, I do not recall what the price difference was between the two at the time and they were my only options available at the time.

[garikfox]

Yeah there's only like 4 choices for magazines and with a 20rd there's only like 2 choices the AA/E's and the AR Stoners. I don't really like steel mags though, oh well it's fine for now I guess

[biodsl]

Wow you guys were right these steel mags are very hard to fill up. They hold 24rds and I could barely push in the 20th rd. wow lol

At the recommendation of other forum members, I've found loading the Elanders and letting them sit for a few weeks helps reduce some of that spring tension.

[LRRPF52]

Here are most of the magazine choices:

CProducts
ASC
Duramag
Amend2 Polymer 10rd
Elander
DSC

I have been using CPRoducts mostly from 2009-2014, then started using some of the Elanders in addition to my CProducts, then got the Amend2 polymer mags when they came out, and recently ordered a bunch of ASC 25rd mags.

I’m mostly shooting through the 17.6” or 12” Grendel lately with all of the above.

I de-edge, blend, and polish my feed ramps on all barrel extensions though, as well as make sure the ejector has a radius on it to ensure reliability.

Right side magazine feed presentation can hang-up on an ejector if they ejector is too long or has a really sharp edge, due to how wide Grendel case heads are.

I’ve never had it happen because I do the ejector work before assembly on every upper I’ve built.

[Double Naught Spy]

Also, there are AR Stoner mags available via MidwayUSA.

I have used Elander mags. I found they tend to bind mid stack, but not consistently. Mine are relegated to being range mags. I bought 2 and both have issues. Won't buy more.

[garikfox]

Thanks, yes this is what i'm going to do, I think I'll do a month heh

[garikfox]

At the recommendation of other forum members, I've found loading the Elanders and letting them sit for a few weeks helps reduce some of that spring tension.

Thanks, yes this is what i'm going to do, I think I'll do a month heh

[garikfox]

Here are most of the magazine choices:

CProducts
ASC
Duramag
Amend2 Polymer 10rd
Elander
DSC

I have been using CPRoducts mostly from 2009-2014, then started using some of the Elanders in addition to my CProducts, then got the Amend2 polymer mags when they came out, and recently ordered a bunch of ASC 25rd mags.

I’m mostly shooting through the 17.6” or 12” Grendel lately with all of the above.

I de-edge, blend, and polish my feed ramps on all barrel extensions though, as well as make sure the ejector has a radius on it to ensure reliability.

Right side magazine feed presentation can hang-up on an ejector if they ejector is too long or has a really sharp edge, due to how wide Grendel case heads are.

I’ve never had it happen because I do the ejector work before assembly on every upper I’ve built.

Thanks for the info, The Amend2 are what I really want but they don't have the capacity I want.

[garikfox]

Also, there are AR Stoner mags available via MidwayUSA.

I have used Elander mags. I found they tend to bind mid stack, but not consistently. Mine are relegated to being range mags. I bought 2 and both have issues. Won't buy more.

I'm going to order some AR Stoner mags to try.

[Klem]

I don't really like steel mags though, oh well it's fine for now I guess

Garik,

One good thing about steel mags is they can give you a little more room. Our cartridge OAL is whatever the chamber and mag will allow, whichever is shorter. SAAMI lists max 57.40mm, but ASC mags allow up to 58mm. In a relatively slow calibre it all helps.

[garikfox]

I guess i can't knock them before I try them. I'm so used to the plastic ones, these metal ones its like I'm in Vietnam lol

[eggman918]

I have been using this on the components of all my steel mags for decades, It has many uses where lube/protection are needed and dust/grit are not...$.02
https://www.crcindustries.com/dry-moly-lube-11-wt-oz/