6.5 Grendel Forum › 6.5 GRENDEL DISCUSSION FORUMS › 6.5 Grendel ARs and Other Semi-Autos v
Lapping ar15 uppers

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Linear Mode
Lapping ar15 uppers
Wheelhorse Offline
Member
***
Posts: 243
Threads: 13
Joined: May 2014
#16
01-26-2020, 05:22 PM
You might want to keep an eye on the cutting surface of your lapping tool after you've done a few because the steel it's made from wears too.
Mine has been chucked in a lathe and redressed a couple of times.
Find
Reply


Messages In This Thread
Lapping ar15 uppers - by sbowhuntr - 01-21-2020, 02:21 PM
Lapping ar15 uppers - by mdram - 01-21-2020, 02:32 PM
Lapping ar15 uppers - by grayfox - 01-21-2020, 02:37 PM
Lapping ar15 uppers - by grayfox - 01-21-2020, 02:47 PM
Lapping ar15 uppers - by A5BLASTER - 01-21-2020, 03:10 PM
Lapping ar15 uppers - by FLshooter - 01-21-2020, 11:56 PM
Lapping ar15 uppers - by Mustangfreek - 01-21-2020, 11:58 PM
Lapping ar15 uppers - by A5BLASTER - 01-22-2020, 12:07 AM
Lapping ar15 uppers - by FLshooter - 01-22-2020, 12:24 AM
Lapping ar15 uppers - by sbowhuntr - 01-22-2020, 02:39 AM
Lapping ar15 uppers - by A5BLASTER - 01-22-2020, 03:35 AM
Lapping ar15 uppers - by 1075 tech - 01-22-2020, 01:46 PM
Lapping ar15 uppers - by FLshooter - 01-22-2020, 05:54 PM
Lapping ar15 uppers - by sbowhuntr - 01-22-2020, 10:05 PM
Lapping ar15 uppers - by 402joel - 01-26-2020, 04:13 PM
Lapping ar15 uppers - by Wheelhorse - 01-26-2020, 05:22 PM
Lapping ar15 uppers - by Msalm - 02-01-2020, 02:11 PM
Lapping ar15 uppers - by Old Bob - 02-02-2020, 04:24 PM
Lapping ar15 uppers - by meatsweats - 02-02-2020, 07:44 PM
Lapping ar15 uppers - by LRRPF52 - 02-03-2020, 03:53 PM
Lapping ar15 uppers - by Msalm - 02-04-2020, 01:35 PM
Lapping ar15 uppers - by Mesa1978 - 02-04-2020, 10:10 PM
Lapping ar15 uppers - by mdram - 02-05-2020, 05:34 PM
Lapping ar15 uppers - by guitarhillbilly - 02-05-2020, 05:41 PM
Lapping ar15 uppers - by Mad Charlie - 02-08-2020, 06:38 AM
Lapping ar15 uppers - by dlraymond30 - 02-27-2020, 12:14 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)