09-28-2017, 08:46 PM
I built a 10.5 5.56 SBR from a 80% lower and never had any issues getting stamp.....with a 80% lower you can determine model no. and s/n and have it engraved that way....
|
Form 1 SBR questions
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 01:58 PM
Form 1 SBR questions - by Bigs28 - 09-26-2017, 02:13 PM
Form 1 SBR questions - by Troutguide - 09-26-2017, 02:22 PM
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 02:32 PM
Form 1 SBR questions - by mongoosesnipe - 09-26-2017, 02:38 PM
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 02:56 PM
Form 1 SBR questions - by Troutguide - 09-26-2017, 02:59 PM
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 03:03 PM
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 03:14 PM
Form 1 SBR questions - by Troutguide - 09-26-2017, 03:24 PM
Form 1 SBR questions - by Kswhitetails - 09-26-2017, 03:36 PM
Form 1 SBR questions - by Troutguide - 09-26-2017, 04:06 PM
Form 1 SBR questions - by mongoosesnipe - 09-26-2017, 05:13 PM
Form 1 SBR questions - by explorecaves - 09-26-2017, 07:07 PM
Form 1 SBR questions - by LRRPF52 - 09-26-2017, 10:11 PM
Form 1 SBR questions - by Kswhitetails - 09-27-2017, 02:40 AM
Form 1 SBR questions - by explorecaves - 09-27-2017, 10:57 AM
Form 1 SBR questions - by Kswhitetails - 09-27-2017, 01:11 PM
Form 1 SBR questions - by LRRPF52 - 09-27-2017, 05:01 PM
Form 1 SBR questions - by Kswhitetails - 09-27-2017, 07:06 PM
Form 1 SBR questions - by explorecaves - 09-27-2017, 07:48 PM
Form 1 SBR questions - by Troutguide - 09-27-2017, 07:49 PM
Form 1 SBR questions - by Kswhitetails - 09-27-2017, 08:03 PM
Form 1 SBR questions - by explorecaves - 09-28-2017, 01:18 AM
Form 1 SBR questions - by Kswhitetails - 09-28-2017, 02:53 AM
Form 1 SBR questions - by explorecaves - 09-28-2017, 01:13 PM
Form 1 SBR questions - by Kswhitetails - 09-28-2017, 02:18 PM
Form 1 SBR questions - by HowaGrendel - 09-28-2017, 08:46 PM
Form 1 SBR questions - by Troutguide - 09-26-2017, 03:10 PM
|
Users browsing this thread: 1 Guest(s)