6.5 Grendel Forum › 6.5 GRENDEL DISCUSSION FORUMS › 6.5 Grendel ARs and Other Semi-Autos v
grahhhhh

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Threaded Mode
grahhhhh
jwilson1985
Unregistered
 
#1
10-10-2011, 01:54 AM
cerakoted the grendel got all the way to the oven and KABOOM dropped it ...lucky for me cerakote dosent set up intill it cures in the oven so i have this sweet smug :mad:
Reply
LRRPF52
Unregistered
 
#2
10-10-2011, 04:05 PM
The smudges are best dealt with by baking them, then grinding them off, re-coating, and baking again. When they smudge, they really smudge.
Reply
Sniper20
Unregistered
 
#3
10-10-2011, 04:43 PM
I told you that you shouldn't have eaten that popcorn... Smile
Reply
noone
Unregistered
 
#4
10-10-2011, 07:36 PM
LRRPF52 Wrote:The smudges are best dealt with by baking them, then grinding them off, re-coating, and baking again. When they smudge, they really smudge.

That sounds like the voice of experience gained from an unfortunate incident. Good info to have though.
Reply
noone
Unregistered
 
#5
10-10-2011, 07:39 PM
Speaking of cerakoting, who do folks here know of that does nice cerakote work on parts sent to them? Although I had a great experience with Brooks coatings in Sherwood, Oregon, I'm always looking for anyone who does nice work at reasonable prices.
Reply
LRRPF52
Unregistered
 
#6
10-10-2011, 07:53 PM
I think both I and jwilson1985 do it. I had one of my uppers that I was looking over in bright light to ensure I had 100% coverage of the part, when I dropped it on the cement. It picked up dirt particles, sand, and other debris. I had to brush off as much of that as I could, bake it, and grind down the smudges, then coat and bake again. This is not your typical Duracoat or PTFE-based paints with epoxy hardener. It is literally a ceramic mud at a microscopic level that is mixed with a hardener, then baked-on for 2 hours. It is extremely difficult to remove with grinding or wire brush wheels, and just kinda polishes over if you don't use something aggressive.
Reply
warped
Unregistered
 
#7
10-10-2011, 08:38 PM
Templar does it as well, LRRPF52 and JWilson are competent also.

If you need something really complex call Templar
Reply
WillD
Unregistered
 
#8
10-10-2011, 10:22 PM
Danger Close Outfitters here did a fine job on mine!
Reply
stanc Offline
Banned
Posts: 4,033
Threads: 106
Joined: Apr 2011
#9
10-11-2011, 08:59 PM
LRRPF52 Wrote:This is not your typical Duracoat or PTFE-based paints with epoxy hardener. It is literally a ceramic mud at a microscopic level that is mixed with a hardener, then baked-on for 2 hours.
Then Cerakote is not for plastic stocks, grips, forends, etc?
Find
Reply
LRRPF52
Unregistered
 
#10
10-11-2011, 09:03 PM
For the plastic parts, you bake it on at a lower temperature as to not melt it. It can be applied to wood & plastic and baked without issue at 200 F.
Reply
jwilson1985
Unregistered
 
#11
10-11-2011, 10:36 PM
they also have the air cure for plastic/wood and scope but it takes 7 days to fully cure ,not
Reply
jwilson1985
Unregistered
 
#12
10-13-2011, 07:04 AM
well got it all done ill post pics soon and have sum pics of sum others to put up and one lil gat stocked ar just for you LR
Reply
jwilson1985
Unregistered
 
#13
10-16-2011, 11:45 PM
well got them done 50 beowulf and the 6.5
[Image: ls1204.jpg]
Reply
jwilson1985
Unregistered
 
#14
10-16-2011, 11:46 PM
other scope for wulf should be in ,in a week
Reply
Sniper20
Unregistered
 
#15
10-17-2011, 01:26 PM
Beautiful work. They look awesome!
Reply
jwilson1985
Unregistered
 
#16
10-17-2011, 10:20 PM
Sniper20 Wrote:Beautiful work. They look awesome!

thank you man
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)