First time out with my Grendel - Printable Version +- 6.5 Grendel Forum (https://65grendel.com) +-- Forum: 6.5 GRENDEL DISCUSSION FORUMS (https://65grendel.com/forumdisplay.php?fid=3) +--- Forum: 6.5 Grendel ARs and Other Semi-Autos (https://65grendel.com/forumdisplay.php?fid=8) +--- Thread: First time out with my Grendel (/showthread.php?tid=7673)

First time out with my Grendel - outlaw45 - 04-06-2014 Finally ready to shoot my Grendel and zero my scope. I was shooting factory Hornday 123 A-max. I a have a Syrac adjustable gas block so I needed to adjust that too. I fired one round until the bolt would lock back. Once it did that I opened it a half turn more. During this progression I noticed the case mouths started to get dented or bent when they were ejected. Is this normal for the Grendel? Also I was using an Alexander Arms 10 round magazine. I noticed the follower wouldn't always catch the bolt stop and push up to lock the bolt back. Compared to another magazine AR-Stoner that I have the AA mag has more play in the follower forward and backwards. If the follower is pushed forward in the mag the bolt stop won't be caught and the bolt closes. I think its a bad magazine. I have 2 more AR-Stoner mags to compare to, but haven't fired them in the gun yet. First time out with my Grendel - CPT.CRAZY - 04-06-2014 Not sure on the mag, it looks like a bad mag to me, I've had no problems with the AR Stoner mags. The bent cases can be caused by slight under gas assuming your upper has a shell deflector. First time out with my Grendel - NugginFutz - 04-06-2014 You can do what many others have, and stick some velcro (fuzzy half) to the deflector. A search for ejector spring tuning will show you another option, as well, but this method demands your careful attention and the potential need for a spare ejector/takedown detent spring. If you are still slightly under gassed, it can result in your failure to lock back, as well. Opening the gas block a bit more just might clear that up. First time out with my Grendel - outlaw45 - 04-07-2014 I thought I would be over gassed if I was getting dented necks. First time out with my Grendel - LRRPF52 - 04-07-2014 You can dial down the gas some, but I wouldn't recommend it, especially in Iowa, where the temp shift covers a wide range throughout the year. I have never been bothered by dented mouths, as they resize the same. How does she shoot? First time out with my Grendel - waveslayer - 04-07-2014 place a piece of Velcro on the brass deflector, that will solve it, I had the same issue once upon a time. First time out with my Grendel - rebelsoul - 04-08-2014 Outlaw, I had a bolt catch that was to short nosed. Can you compare yours to another unit? First time out with my Grendel - outlaw45 - 04-08-2014 I didn't know if that was normal for dented mouths or not. I'll try a little more gas but otherwise if should be ok to run. I'll compare the bolt catch to another. I also replaced the follower with another and it looks better. Have yet try it. First time out with my Grendel - outlaw45 - 04-11-2014 Second time out with the with the Grendel. Shooting factory Hornday 123 A-max I shot this 5 shot group, the last one I pulled cause I was getting excited it was so good. Still working with the adjustable gas block. First time out with my Grendel - jawbone - 04-11-2014 "the last one I pulled cause I was getting excited it was so good." I know the feeling. love it. First time out with my Grendel - Blacklab - 04-13-2014 Dam!!!! that's my tee fine.