6.5 Grendel Forum
6.5 Grendel Official C.I.P Listing - Printable Version

+- 6.5 Grendel Forum (https://65grendel.com)
+-- Forum: 6.5 GRENDEL DISCUSSION FORUMS (https://65grendel.com/forumdisplay.php?fid=3)
+--- Forum: 6.5 Grendel Ammunition & Reloading (https://65grendel.com/forumdisplay.php?fid=10)
+--- Thread: 6.5 Grendel Official C.I.P Listing (/showthread.php?tid=7346)

6.5 Grendel Official C.I.P Listing - Kohoki - 02-19-2014

Dear all,

maybe you would like to know that the 6.5 Grendel has a C.I.P listing since May 2013:

http://www.cip-bobp.org/homologation/de/tdcc_public?page=2&cartridge_type_id=1

Technical Datasheet:

http://www.cip-bobp.org/homologation/uploads/tdcc/tab-i/6-5-grendel-ge.pdf

6.5 Grendel Official C.I.P Listing - Dogue - 02-19-2014

Here's the english version, for those of us on this side of the pond.

http://www.cip-bobp.org/homologation/uploads/tdcc/tab-i/6-5-grendel-en.pdf

6.5 Grendel Official C.I.P Listing - Kohoki - 02-19-2014

Would it be intelligent to make this thread a sticky?

6.5 Grendel Official C.I.P Listing - JASmith - 02-19-2014

Kohoki Wrote:Would it be intelligent to make this thread a sticky?

Darned Right! Alternatively, post it on the same page as the SAAMI link. Makes for a cleaner sticky list.

Cheers!

6.5 Grendel Official C.I.P Listing - m796rider - 02-19-2014

jasmith Wrote:males for a cleaner sticky list.

Cheers!

lol... Smile

6.5 Grendel Official C.I.P Listing - BluntForceTrauma - 02-19-2014

Thanks for the link! Very cool. Now, is it too much to ask all "6.5 Grendel" barrel makers to follow this to the letter? Wink

John

P.S. I've combined both SAAMI and CIP into a new sticky. Thanks all for posting these.

6.5 Grendel Official C.I.P Listing - JASmith - 02-19-2014

m796rider Wrote:lol... Smile

Guess my eyes hadn't started to focus well enough when I posted. Nonetheless that's a good laugh on me!

Thanks!

6.5 Grendel Official C.I.P Listing - BjornF16 - 02-20-2014

I don't see the compound angle on the CIP chamber drawing...just the 1.5 degrees

6.5 Grendel Official C.I.P Listing - JASmith - 02-20-2014

BjornF16 Wrote:I don't see the compound angle on the CIP chamber drawing...just the 1.5 degrees

...but the dimension "G1" = 6.65 mm which converts to 0.2618 inches. This is awfully close to the 0.2617" at the same location of the SAAMI chamber. Both are smaller than the bullet diameter. This suggests that a taper between the start of teh freebore to this location exists.

I am still trying to find a call out for the diameter of the throat just in front of the neck. I can find the diameter, Z1 which is the groove or bullet diameter. I speculate that the dimension is implied to be the start of the free bore.