+- 6.5 Grendel Forum (https://65grendel.com)
+-- Forum: 6.5 GRENDEL DISCUSSION FORUMS (https://65grendel.com/forumdisplay.php?fid=3)
+--- Forum: 6.5 Grendel ARs and Other Semi-Autos (https://65grendel.com/forumdisplay.php?fid=8)
+--- Thread: gas bloc hack (/showthread.php?tid=19829)
gas bloc hack - ulmapache - 10-29-2019
When attaching your gas block...grab a couple of feet of 1/4 inch id plastic tube to go over the gas tube in your upper...if you smoke, blow some smoke in the tube..if the smoke comes out the barrell, you've got the gas bloc set correctly...if you don't, grab someone who does... Works well...
gas bloc hack - A5BLASTER - 10-29-2019
Wotejk makes a gas block that has a top screw you can remove and look down into the block and line up the gas port.
gas bloc hack - 41bear - 10-29-2019
A5BLASTER Wrote:Wotejk makes a gas block that has a top screw you can remove and look down into the block and line up the gas port.
They now have a hole there and I use a drill bit, put down thru the gas hole, to aline and then tighten the 3 clamp screws, easy as pie
gas bloc hack - ulmapache - 10-29-2019
Hmmm...might have to change brands on the next build...good idea there with the sight hole...
gas bloc hack - joedirt199 - 10-29-2019
Or just drill a hole through a regular gas block.
gas bloc hack - keystone183 - 10-29-2019
These work great. But slightly modified toothpics are cheaper....
https://hbindustries.net/store/shop/ar15-gas-block-aligner-5-56mm/
gas bloc hack - ARErector - 10-31-2019
keystone183 Wrote:These work great. But slightly modified toothpics are cheaper....
https://hbindustries.net/store/shop/ar15-gas-block-aligner-5-56mm/
That's a pretty good idea with the toothpick.
Another member suggested spaghetti. That sounded good too, but I haven't had a chance to try it yet.
gas bloc hack - snarkscarbine - 11-02-2019
A5BLASTER Wrote:Wotejk makes a gas block that has a top screw you can remove and look down into the block and line up the gas port.
Great shape to the gas block/design, but their adjustment screws are GARBAGE.
gas bloc hack - A5BLASTER - 11-02-2019
snarkscarbine Wrote:Great shape to the gas block/design, but their adjustment screws are GARBAGE.
I haven't had the first bit if problems out of mine. Sure it wasn't user failure?
gas bloc hack - gmar - 11-03-2019
I?ve never seen the pin alignment tool or heard of using toothpicks or spaghetti. Both are great ideas. I?ve always just used a sharpie to draw a line from my gas port past my gas block on both sides. Then I just make sure my gas tube is in line with the sharpie line.
gas bloc hack - PGW Steve - 11-04-2019
I've used a bore scope.
gas bloc hack - Javman - 11-04-2019
Just plug the chamber end with one of the foam ear plugs, slip the gas block with tube attached and move the gas block while blowing air through the muzzle and set where you can feel the minimum resistance in air coming out the gas tube and tighten her up.
gas bloc hack - outbreaker - 11-04-2019
keystone183 Wrote:These work great. But slightly modified toothpics are cheaper....
https://hbindustries.net/store/shop/ar15-gas-block-aligner-5-56mm/
I started using those and love them.
gas bloc hack - centerfire - 11-10-2019
Drill dimples aligned with the gas port and then cross drill and pin the block if you so desire. No cancer necessary.
![[Image: TzN1CXa.jpg]](https://i.imgur.com/TzN1CXa.jpg)