+- 6.5 Grendel Forum (https://65grendel.com)
+-- Forum: 6.5 GRENDEL DISCUSSION FORUMS (https://65grendel.com/forumdisplay.php?fid=3)
+--- Forum: 6.5 Grendel Troubleshooting (https://65grendel.com/forumdisplay.php?fid=15)
+--- Thread: Problem with bolt stop spring installation ? (/showthread.php?tid=18069)
Problem with bolt stop spring installation ? - Kevinohio - 01-21-2019
Had a problem with the bolt stop spring that goes in the hole under the lever.it was like it was to big at one end.wouldnt fit the hole one way.but turn it the other way it fit inside the hole.bolt not push down like it was sopose to.so I put the little steel piece in the hole first and then the spring.it worked then.but the end of the spring is against the lever that releases the bolt.will this be ok?
Problem with bolt stop spring installation ? - just_john - 01-21-2019
Without a picture, sounds like you have the seer spring instead of the stop spring. The correct spring is the same diameter full length and about 1/2" long.
Problem with bolt stop spring installation ? - NugginFutz - 01-21-2019
You have the wrong spring. The bolt catch spring is non-tapered. Get another LPK for the spring, and keep the rest for spares. OR special order the spring by itself and pay nearly the same amount.
I'm sure, though, that someone on the board can source the correct spring for less money than I can.
ETA: When assembling your receivers, be careful not to mix the parts from your different assemblies. Keep your Upper and Lower Parts kit components separate from the trigger group components. After a few builds, these become familiar but, in the meantime, take the time to positively identify the various springs, pins, etc.
Problem with bolt stop spring installation ? - Kevinohio - 01-21-2019
[quote=just_john]Without a picture, sounds like you have the seer spring instead of the stop spring. The correct spring is the same diameter full length and about 1/2" long.[/QUOTE
I think I installed the longer spring for the sear.is the sear spring longer? also if I got wrong spring in wrong place.will this make the sear not be right to.
Problem with bolt stop spring installation ? - Drillboss - 01-21-2019
See if this helps. https://www.pewpewtactical.com/wp-content/uploads/2016/07/Lower-Kit-ar15.com_.gif
Problem with bolt stop spring installation ? - Kevinohio - 01-21-2019
You guys was right.i took it apart and the springs was in wrong place.so I replaced them and put it back togather.now my role pin to the bolt stop is messed up.
Problem with bolt stop spring installation ? - JohnXDm - 01-21-2019
Definitely sounds like the disconnector spring. You should also check your trigger assembly to ensure the disconnector isn't using the bolt catch spring.
https://www.opticsplanet.com/cmmg-inc-ar15-spring-bolt-catch.html
Problem with bolt stop spring installation ? - JohnXDm - 01-21-2019
Take a breath, don't forget to put painters tape or masking tape on the side of your receiver to protect from damage when you miss while driving the pin. Get yourself one of these.
https://www.primaryarms.com/anderson-manufacturing-oops-kit-am-556-lw-oops-kit
https://www.opticsplanet.com/cmmg-inc-ar15-pin-roll-bolt-catch.html
Problem with bolt stop spring installation ? - Kevinohio - 01-21-2019
I used tape all around my reciever to protect it.i found a roll pin for 50 cents.but it cost 5 dollars or so to ship it.lol
Problem with bolt stop spring installation ? - VASCAR2 - 01-21-2019
Many auto parts (NAPA) store and hardware stores (Ace) sell compression and roll pins. Even if the pin is a little long you can cut the pin to the length you need.
Problem with bolt stop spring installation ? - Kevinohio - 01-21-2019
VASCAR2 Wrote:Many auto parts (NAPA) store and hardware stores (Ace) sell compression and roll pins. Even if the pin is a little long you can cut the pin to the length you need.
Ok thanks
Problem with bolt stop spring installation ? - Wargrendeleagle - 01-21-2019
If you have a harbor freight close they sell kits with hundreds of various sized roll pins. Obviously most won't be the size you need but I bet you can find one. And use a 20% off coupon and can get them cheap
Problem with bolt stop spring installation ? - Kevinohio - 01-22-2019
Wargrendeleagle Wrote:If you have a harbor freight close they sell kits with hundreds of various sized roll pins. Obviously most won't be the size you need but I bet you can find one. And use a 20% off coupon and can get them cheapClosest one is about 60 miles from me
Problem with bolt stop spring installation ? - Wargrendeleagle - 01-22-2019
Well it was worth a shot. Thats too far to drive for a roll pin! I'll probably get a box next time I go to test it. I'm real good at boogering up a gas block roll pin
Problem with bolt stop spring installation ? - Kevinohio - 01-22-2019
eBay has some and free shipping.i got two USA made ones for 2.50.they had ten for that price to.but I got the stainless steel ones.
Problem with bolt stop spring installation ? - VASCAR2 - 01-22-2019
Just for future reference here are the pin sizes for AR-15’s
A1 Rear Sight Wheel Retaining Pin.................1/16x1/4
Trigger Guard Detent Pin................................1/16x1/4
Forward Assist Pawl Pin(new round)..............1/16x1/4
Forward Assist Pawl Pin(Old teardrop)...........1/16x5/16
Gas Tube Pin...................................................5/64x5/16
Charging Handle Latch pin..............................5/64x5/16
Bolt Catch Retaining Pin..................................3/32x1/2
Forward Assist Pawl Pin.................................3/32x1/2
Forward Assist Retaining Pin..........................3/32x5/8
Type D Stock Swivel Retaining Pin.................1/8x7/16
Front Sling Swivel Pin......................................1/8x1/2
Trigger Guard Pivot Pin...................................1/8x5/8
Rifle Buffer Pad Retaining Pin..........................1/8x3/4
Type D Stock Swivel Bracket Retaining Pin....1/8x7/8
Problem with bolt stop spring installation ? - Kevinohio - 01-22-2019
Ok thanks you all have been very helpful.
Problem with bolt stop spring installation ? - FRB6.5 - 01-25-2019
Much more pricey than a roll pin but far less annoying to install:
https://www.knsprecisioninc.com/product/kns-precision-inc-bolt-catch-retaining-pin/