+- 6.5 Grendel Forum (https://65grendel.com)
+-- Forum: INDUSTRY PARTNERS (https://65grendel.com/forumdisplay.php?fid=7)
+--- Forum: Rexus Outfitters (https://65grendel.com/forumdisplay.php?fid=37)
+--- Thread: SOLD OUT MONSTER Ultra-Lite Flash Suppressor (/showthread.php?tid=20988)
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - BluntForceTrauma - 08-01-2020
U P D A T E: Just made a mail run and all orders from yesterday and today are on their way!
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - A5BLASTER - 08-03-2020
Finally got off my backside and got a flash hider ordered.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - spoon - 08-06-2020
I was getting ready to place an order when I noticed the checkout page is not secured. I attached a screenshot.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - SDW - 09-08-2020
BluntForceTrauma Wrote:Hand-tightened. I suppose if one didn't feel that was enough, one could wrap some tape on a screwdriver and gently torque it a bit. Or a drop of Loctite. Or a crush washer. Or Advanced Armament Corp (AAC) has a tool if one wants to get fancy.I mentioned in an earlier post that it would be good to fine a much less expensive alternative to that $40 tool. After a long while I decided finally to search for one, in case anyone (like me) wants to get fancy but doesn't want to shell out almost $50.
Thorsden Customs sells an interesting little one that sells for only $10 (+ $4 to mail it). I ordered one and will report back, in case anyone else is interested:
https://www.thordsencustoms.com/3-pronged-flash-hider-wrench/.html
The above tool is designed ideally for the subbier old GI type M16 three prong, but I don't know yet that it won't work fine with this Grendel flash suppressor. I don't imagine that very much torque is actually needed.
Additionally, Surefire also sells a wrench (socket?) for their own make of three-prong flash suppressors. It may also work fine with these new low-profile Grendel FSs. And it's also just $10:
https://www.surefire.com/products/suppressors-division/suppressor-accessories/socom-3-prong-installation-wrench/
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - jonny rotton - 10-31-2020
i finally tested one tonight on a 12" grendel with wolf ammo. they really do work very well,
thanks bft i will order a couple more right now.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - BluntForceTrauma - 02-05-2021
U P D A T E : Just five left! Lightweight, three-prong flash suppressor with diameter of 0.740 so that 0.750 gas blocks can slide right over. Very effective for low-light shooters!
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - TruLbrt - 02-06-2021
Quote:Thorsden Customs sells an interesting little one that sells for only $10 (+ $4 to mail it). I ordered one and will report back, in case anyone else is interested:
https://www.thordsencustoms.com/3-pr...r-wrench/.html
Tried this for my monster barrel and monster flash suppressor.
Fits well but short so max torque is low (15lbs) before the flash supressing prongs start to flex. I observed no distortion afterwards.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - Les - 02-12-2021
Pretty sexy, if I didn't shoot suppressed, I'd buy a few. Love the design BFT.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - SDW - 02-19-2021
TruLbrt Wrote:Tried this for my monster barrel and monster flash suppressor.Yeah that's true. (BTW, I assume those "lbs" are ft-lbs, not inch-lbs.) However, the tool does allow you to go well beyond just "hand tightening" and it's much better than jamming a screwdriver though the prongs to apply torque.
Fits well but short so max torque is low (15lbs) before the flash supressing prongs start to flex. I observed no distortion afterwards.
The Surefire wrench dealie might be better if you're looking to make it tighter. FWIW, my Thorsden tool also works perfectly on my Vietnam era three-prong FS.
SOLD OUT MONSTER Ultra-Lite Flash Suppressor - 41bear - 03-13-2021
What's the latest ETA on getting these back in stock? I'll order a couple more the second they show up.